Get Perfect Results with Premium 300-515 Dumps Updated 178 Questions
Free 300-515 Exam Study Guide for the NEW Dumps Test Engine
Cisco 300-515 exam is designed for IT professionals who specialize in implementing Cisco Service Provider VPN Services. 300-515 exam focuses on testing the candidate's knowledge and skills in deploying and configuring VPN services, including MPLS Layer 3 VPNs, Layer 2 VPNs, and VRF-Lite.
Cisco 300-515 certification exam, also known as Implementing Cisco Service Provider VPN Services, is designed for professionals who work with service provider networks. 300-515 exam is designed to validate the skills required to implement a service provider virtual private network (VPN) solution, including configuring, deploying, and troubleshooting VPN solutions in a service provider environment. Passing 300-515 exam is a key step toward becoming a Cisco Certified Specialist – Service Provider VPN Services Implementation.
NEW QUESTION # 50
What must match in the EVPN and L2VPN configuration mode when configuring EVPN native in a router?
- A. bridge domain
- B. EVI
- C. interface
- D. address family
Answer: B
Explanation:
Section: Layer 2 VPNs
Explanation/Reference: https://www.cisco.com/c/en/us/td/docs/routers/asr9000/software/asr9k-r6-2/lxvpn/configuration/ guide/b-l2vpn-cg-asr9000-62x/b-l2vpn-cg-asr9000-62x_chapter_01011.html
NEW QUESTION # 51
A service provider that implements large L2VPNs received a request to implement EVPN Native to improve a customer's Layer 2 communication across the core. MPLS is configured in the core to support VPN transport. Which action must the engineer take as part of the implementation?
- A. Configure the customer EVPN to advertise MAC addresses over the core.
- B. Configure MPLS TE between PEs to support MAC address learning over the core where EVPN is disabled.
- C. Configure EVPN to support IP traffic only and disable MPLS to improve efficiency.
- D. Configure a pseudowire between the CEs to allow for Layer 2 to be extended beyond the EVPN configuration.
Answer: A
Explanation:
EVPN-Native relies on BGP to distribute MAC-IP bindings (via Type-2 MAC routes) so that each PE's software MAC table stays synchronized without flooding. Enabling MAC advertisement in the EVPN control plane is the key step: it tells each PE to learn and push customer MAC entries into MP-BGP and thus across the MPLS core.
NEW QUESTION # 52
Which kind of traffic is supported in an MVPN Extranet?
- A. Bidirectional PIM
- B. PIM dense mode with Reverse Path Forwarding
- C. PIM dense mode
- D. PIM sparse mode
Answer: D
Explanation:
Reference:
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipmulti_mvpn/configuration/xe-16/imc-mvpn-xe-
16-book/imc-mc-vpn-extranet.html
NEW QUESTION # 53
SIMULATION 4
Guidelines
This is a lab item in which tasks will be performed on virtual devices.
Refer to the Tasks tab to view the tasks for this lab item
Refer to the Topology tab to access the device console(s) and perform the tasks.
Console access is available for all required devices by clicking the device icon or using the
tab(s) above the console window.
All necessary pre-configurations have been applied.
Do not remove any existing configurations from the devices, only those necessary to make the
appropriate changes required to fulfill the listed tasks.
Do not change the enable password or hostname for any device.
Save your configurations to NVRAM before moving to the next item.
Click Next at the bottom of the screen to submit this lab and move to the next question.
When Next is clicked, the lab closes and cannot be reopened.
Topology
Tasks
Routers R1 through R4 implement Ethernet Operations, Administration, and Maintenance operations.
Perform the below configuration on R1 and R4.
Configure E-OAM on interface E0/0.
Configure link monitoring:
- Monitor error frames
- Set a high threshold equal to 400
- Set threshold action equal to error-disable
The initial configuration with IP addressing has been completed. Do not change the configurations except to fulfill the abovementioned tasks.
Answer:
Explanation:
The commands enable Ethernet OAM on interface e0/0, start link-monitoring for errored frames, set the high-error threshold to 400 frames, and specify that the interface is put into err-disable state if that threshold is exceeded, exactly matching the requested behavior.
NEW QUESTION # 54
Which two BGP attributes prevent loops in a route reflector environment? (Choose two.)
- A. local preference
- B. origin
- C. cluster ID
- D. AS_PATH
- E. originator ID
Answer: C,E
NEW QUESTION # 55
Refer to the exhibit. Router 1 is a P router in the ISP MPLS core.
A connected P router cannot generate an MPLS label for the router 1 loopback0 interface.
Which action resolves this issue?
- A. The loopback0 interface must be in OSPF area 0.
- B. The network statement under the routing process must have a wildcard mask of 0 0.0 255.
- C. A static route to null 0 must be added for the loopback interface and then static routes must be redistributed into OSPF
- D. The OSPF network type must be changed on loopback0 to point-to-point
Answer: B
NEW QUESTION # 56
How does a virtual machine move seamlessly within a network in an EVPN environment?
- A. The IP-to-MAC binding for the default gateway is maintained across the network independent of the location of the virtual machine.
- B. A central server automatically assigns a new IP address to the virtual machine via dial-out.
- C. The virtual machine sends out a broadcast message after changing locations to seamlessly identify its new default gateway.
- D. The administrator updates the MAC address of the virtual machine in the CAM table after the virtual machine is moved.
Answer: A
Explanation:
EVPN uses an anycast gateway and distributes MAC+IP (ARP/NDP) bindings via BGP. Because every PE advertises the same gateway MAC and knows the host's MAC/IP binding, the VM can move to a new PE - its L2 adjacency and default gateway remain unchanged, yielding seamless mobility.
NEW QUESTION # 57
Refer to the exhibit. An organization is running H-VPLS on a network comprising four routers in a hub-and-spoke topology with R1 as the hub.
An engineer added a new spoke with multiple VCs to the network, and now traffic cannot flow properly.
How should the engineer update the configuration on R1 to correct the problem?
- A. Disable Cisco Discovery Protocol to allow MPLS to share labels between the designated spokes
- B. Disable Cisco Discovery Protocol to allow for neighbor discovery
- C. Disable spanning tree to allow loops to occur within the hub-and-spoke topology.
- D. Disable split horizon to allow multiple VCs per spoke
Answer: D
NEW QUESTION # 58
An ISP provides a major client MPLS VPN for managed services. The MPLS engineering team needs to use the advanced VPN feature of selective VRF import so that only specific prefixes are present in the required VPNs.
Which aspect of this feature must the team consider?
- A. A route is imported into the VRF only when at least one RT that is attached to the route matches one RT that is configured in the VRF and the route is permitted by the import route map.
- B. The routers that are imported in the VRF can be BGP and IGP routes, so other match conditions in the route map, besides communities, can be used.
- C. The import-map command is applied under the PE interface that connects to the CE router.
- D. A route must pass the import route map first and then the route target import filter.
Answer: A
Explanation:
Reference:
https://www.ccexpert.us/mpls/configuring-selective-vrf-import.html
NEW QUESTION # 59
Refer to the exhibit. A small company contracted to receive centralized training services from a larger organization. The services are provided via an extranet that is distributed between the organizations across an ISP connection using multicast. Security must be high to ensure that data is not compromised. Which action must be taken at the ISP to implement the required services?
- A. Configure PIM-SM with the RP configured as a P router.
- B. Configure the AS number of the smaller company to be the same as that of the larger organization, and use the AS-Override feature to allow the multicast traffic over the VPN.
- C. Configure SSM and assign the correct range of SSM IP addresses to the default and data MDT groups.
- D. Configure a CSC connection so that the larger organization serves as an ISP and shares services to the smaller company.
Answer: C
Explanation:
By using Source-Specific Multicast, you eliminate the need for RPs and prevent unauthorized sources from injecting traffic into the VPN's multicast trees. Assigning your MDT control and data groups into the SSM range ensures only the trusted training server's IPv4 addresses can be subscribed to, meeting the high-security requirement.
NEW QUESTION # 60
An engineer needs to improve MPLS network management by implementing a set of tools to support the NOC engineers in troubleshooting network failures. Which feature should the engineer implement to check the connectivity of the MPLS LSP between the ingress and egress PE routers?
- A. MPLS-TP
- B. LDP autodiscovery
- C. extended ping
- D. MPLS OAM
Answer: D
Explanation:
Reference:
https://www.cisco.com/c/en/us/td/docs/routers/asr9000/software/asr9k_r5-3/mpls/configuration/guide/b-mpls-cg
NEW QUESTION # 61
How is the underlay label managed in L3VPN data plane operations?
- A. The label is unchanged on provider routers and popped at the egress router.
- B. The label is swapped at each label-switching router in the service provider network.
- C. The label is pushed at the ingress LER and remains unchanged through the MPLS label swap process in the network.
- D. The label is pushed at the provider edge router and popped at the next provider router.
Answer: B
Explanation:
In an MPLS L3VPN, the ingress PE pushes both the VPN (inner) label and a transport (outer) label. Each MPLS LSR in the SP core examines the top (transport) label, swaps it for its next-hop label via its LFIB, and forwards the packet. Only the egress PE pops the transport label before delivering the packet to the CE.
NEW QUESTION # 62
While configuring the VRF Selection feature, you get an error message after typing the below statement:
Router(config)#no vrf selection source 172.16.0.0 255.255.0.0 vrf VRF1
Which action caused this message?
- A. the entry of an inconsistent IP address and mask for VRF Selection
- B. an attempt to configure a VRF instance on an interface that already has VRF Selection configured
- C. an attempt to remove a VRF Selection entry that does not exist
- D. an attempt to configure a VRF Selection table that does not exist
Answer: C
Explanation:
Section: VPN Architecture
Explanation/Reference: https://www.cisco.com/c/en/us/td/docs/ios/12_2/12_2sz/feature/guide/122szvrf.html
NEW QUESTION # 63
How do EFPs distinguish flows?
- A. by associating each flow with a single IP address
- B. by analyzing QoS tags
- C. by identifying one or more VLAN tag with wildcards
- D. by analyzing MPLS labels and QoS tags
Answer: C
Explanation:
Ethernet Flow Points classify and distinguish traffic flows primarily by matching on VLAN tag fields (including VLAN ID, priority, and using wildcards as needed). This lets the network group frames that share those tag characteristics into the same monitored flow.
NEW QUESTION # 64
Refer to the exhibit.
Refer to the exhibit Router 1 is a P router in the ISP MPLS core A connected P router cannot generate an MPLS label for the router 1 loopback0 interface Which action resolves this issue?
- A. The loopback0 interface must be in OSPF area 0.
- B. The network statement under the routing process must have a wildcard mask of 0 0.0 255.
- C. A static route to null 0 must be added for the loopback interface and then static routes must be redistributed into OSPF
- D. The OSPF network type must be changed on loopback0 to point-to-point
Answer: B
NEW QUESTION # 65
A network engineer is implementing Layer 3 MPLS VPNs on Cisco IOS/IOS XE PE routers.
Which PE-to- CE routing protocol requires a separate routing process to be created for each VRF?
- A. OSPF
- B. RIPv2
- C. EIGRP
- D. BGP
Answer: A
NEW QUESTION # 66
......
Cisco 300-515 exam is an important certification for IT professionals who want to validate their skills and knowledge in service provider VPN services. By passing the exam, candidates can demonstrate their expertise to potential employers and clients, and gain a competitive advantage in the job market.
300-515 PDF Dumps Extremely Quick Way Of Preparation: https://braindumps2go.dumpexam.com/300-515-valid-torrent.html
